The Building Code Blog
  • Home
  • Blog
  • About
  • PE Roadmap
  • Tools
    • Allowable Height & Area Calculator - Separated Mixed Occupancy
    • Allowable Height & Area Calculator - Non-Separated Mixed Occupancy
    • Average Grade Plane Calaculator
    • Calculated Fire Resistance for Wood Walls
    • Fire and Smoke Damper Tool
    • Fire Wall/Exterior Wall Intersection Tool
    • Frontage Calculator
    • IBC Occupant Load Calculator
    • Plumbing Fixture Calculator
    • Stair Pressurization Estimator
  • Startup

The Building Code Blog

Safety Glass - A Quick Reference Guide

4/1/2020

22 Comments

 
​About twice a year, I receive a question from an architect regarding safety glazing. Where is it required? Can I provide a different type of glass? Is this manufacturer/model acceptable? Without fail, I always end up revisiting the International Building Code (IBC) to review the requirements before answering the question. So in an effort to save me (and hopefully you) time in the future, I have compiled a quick reference guide for safety glazing. All references are to the 2015 IBC.

Safety Glass

​Practically, safety glazing refers to glass panels or other materials that are manufactured to reduce the likelihood of breaking and to minimize the safety risk if the material does break. From a code compliance standpoint, safety glazing refers to any glazing that meets the requirements of IBC 2406.
 
Glass panes are the most common safety glazing material, but the IBC also recognizes plastic, glass block, and louvered windows as potential options. The IBC does not provide any requirements for the process used to manufacturer safety glazing, it only provides performance requirements. Therefore, both tempered and laminated glass assemblies can qualify as safety glazing, if they meet the IBC 2406 requirements.

​Where Required

IBC 2406.4 identifies 7 locations as hazardous locations that require safety glazing:

Glazing in Doors (IBC 2406.4.1): ​

Glazing in any swinging or sliding door is considered a hazardous location.

Exceptions include:
  1. Glazed openings that are small enough to not allow 3-inch diameter sphere to pass through
  2. Decorative glazing
  3. Curved glazed panels in revolving doors
  4. Glazing in doors of commercial refrigeration cabinets
Glass Door
Glass Near Door

​Glazing Adjacent to Doors (IBC 2406.4.2):

Glazing within 24” horizontally from a door where the bottom of the glazing is less than 60” above the floor is considered a hazardous location. Exceptions include:
  1. Decorative glazing
  2. Situations where a wall is located between the glazing and door
  3. Where the door leads to a closet or storage room less than 3 feet in depth (in that case it must comply with the next section)
  4. In Group R-2 occupancies or one and two family dwelling units, glazing on the latch side and perpendicular to the door in a closed position

Glazing in Windows (IBC 2406.4.3): ​

Glazing where a panel is greater than 9 square feet in area where the bottom is less than 18” from the floor, top is greater than 36” from the floor and within 36” of a walking surface is considered a hazardous location. Exceptions include:
  1. Decorative glazing
  2. Where a minimum 1.5-inch horizontal rail is provided between 34-38 inches above the walking surface to withstand at least 50 lbs/linear foot
  3. The outer pane in multi-pane glazing where the bottom is more than 25 feet above any adjacent surface.
Glass Windo
Glass Guard

Glazing in Guards and Railings (IBC 2406.4.5):

​​Glazing in any guard, railing, balaster panel and in-fill panel is considered a hazardous location.

Glazing in Wet Areas (IBC 2406.4.5):

 Glazing in areas containing hot tubs, spas, whirlpools, saunas, steam rooms, bathtubs, showers and swimming pools where the bottom is less than 60” from the walking surface. There is an exception for when the glazing is more than 60” horizontally from the water’s edge of a bathtub, hot tub, spa, whirlpool or swimming pool.
Glass Near Pool
Glass Near Ramp

Glazing Adjacent to Stairways and Ramps (IBC 2406.4.6): ​

Glazing near stairways and ramps where the bottom is less than 60” above the walking surface is considered a hazardous location. Exceptions include;
  1. Where a guard is provided and the glazing is more than 18” from the railing.
  2. Where the glazing is more than 36” from the walking surface.
​

​Glazing Adjacent to the Bottom of a Stairway Landing (IBC 2406.4.7):

​Glazing near the landing at the bottom of a stairway where the bottom is less than 60” above the landing and within 60” horizontally at an angle of less than 180 degrees from the bottom tread nosing is considered a hazardous location. There is an exception for glazing protected by a guard where the glazing is at least 18” from the guard.
Glass Near Bottom of Stairs
Additionally, glazing located in fire-protection rated or fire-resistance rated glazing installed in fire door and window assemblies is required to be safety glazing (IBC 716.5.8.4 and 716.6.3).

​Design Options

​When safety glazing is required, the most common design option is manufactured glazing panels that are either laminated or tempered. Safety glazing panels are required to be tested to either CPSC 16 CFR Part 1201 or ANSI Z97.1 and must be identified through a label or other means of designation. There is an exception that allow forms of safety glazing other than tempered glass to not be labelled when approved by the AHJ.
 
When tempered glass is used, the glazing must be identified by a manufacture’rs designation that is, “acid etched, sand blasted, ceramic fired, laser etched, embossed, or of a type that once applied, cannot be removed without being destroyed.”
 
In retrofit applications, it may not be desirable to replace existing glazing with new safety glazing panels. There are various film products available that can be applied to existing glazing that will satisfy the code requirements for safety glazing. Some examples include products by 3M, Llumar and Gordon Glass.
  
If using this option, it’s important to determine who applies the label to the glazing once the film is applied. If the installing contractor is applying a label after the film is installed, check with the local authority to verify that this will be acceptable. Since the IBC has fairly stringent requirements on safety for identification of the safety glazing, some AHJs require a permanent label that is etched in to glass.

Conclusion

There are 7 distinct hazardous areas where the IBC requires safety glazing. Technically, any product that meets the requirements of IBC 2406 can be considered safety glazing, but the most common products are tempered and laminated glass. Be sure to verify that the product you select has been tested in accordance with CPSC 16 CFR Part 1201 or ANSI Z97.1
22 Comments

    Archives

    November 2022
    October 2022
    March 2022
    February 2022
    January 2022
    November 2021
    May 2021
    April 2021
    March 2021
    February 2021
    January 2021
    October 2020
    September 2020
    August 2020
    July 2020
    June 2020
    May 2020
    April 2020
    March 2020
    February 2020
    January 2020
    December 2019

    Categories

    All
    Calculators
    Chapter 10 - Means Of Egress
    Chapter 11 - Accessibility
    Chapter 14 - Exterior Walls
    Chapter 1 - Scope And Administration
    Chapter 24 - Glass And Glazing
    Chapter 2 - Definitions
    Chapter 33 - Safeguards During Construction
    Chapter 4 - Special Detailed Requirements
    Chapter 5 - General Building Heights And Areas
    Chapter 6 - Types Of Construction
    Chapter 7 - Fire And Smoke Protection Features
    Chapter 9 - Fire Protection Systems
    Cheat Sheets

    RSS Feed

      Signup to Receive Building Code Blog Updates

    Submit

Home

About

Blog

Contact

Copyright © 2019-2022 The Building Code Blog
The views, opinions, and information found on this site represent solely the author and do not represent the opinions of any other party, including the author's employer and the International Code Council, nor does the presented material assume responsibility for its use.  Local codes and amendments may vary from the code requirements described herein. Fire protection and life safety systems constitute a critical component of public health, safety and welfare and you should consult with a licensed professional for proper design and code compliance.
  • Home
  • Blog
  • About
  • PE Roadmap
  • Tools
    • Allowable Height & Area Calculator - Separated Mixed Occupancy
    • Allowable Height & Area Calculator - Non-Separated Mixed Occupancy
    • Average Grade Plane Calaculator
    • Calculated Fire Resistance for Wood Walls
    • Fire and Smoke Damper Tool
    • Fire Wall/Exterior Wall Intersection Tool
    • Frontage Calculator
    • IBC Occupant Load Calculator
    • Plumbing Fixture Calculator
    • Stair Pressurization Estimator
  • Startup